View UFL-LP-040_642388.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

SMT Ultra-Miniature Coaxial Connectors - Mating Heights Owing to the Lowest Profile and the Lightest
U.FL Series
Meets up to 6 GHz Requirement
Figure 1. Mating Height Comparison (with Hirose Electric Products)
2.4(2.5Max)
U.FL
E.FL
sFeatures
1. Mating Heights Owing to Lowest Profile
Height from the printed circuit board when mates a receptacle with a (right-angle) plug is 2.5 mm maximum. This low Profile is at the world's shortest level.
qSpace Factor of Mated Connector
Figure 2. U.FL-LP-040 and U.FL-R-SMT
2. Extremely Small Board Occupation Area
Dia.0.81 U.FL-R-SMT U.FL-LP-066 Dia.1.13 Dia.1.32
3. World's Lightest
These are the world's lightest coaxial connectors. Receptacle: 15.7 mg Right-angle plugs For O 0.81 mm cable: 53.7 mg For O 1.13 & 1.32 mm cable: 59.1 mg
4. Can Be Used Up to a Frequency of 6 GHz
To meet the frequency requirements of a wide variety of miniature equipment, these connectors offer high frequency performance from DC to 6 GHz. Figure 3. U.FL-LP-066and U.FL-R-SMT
5. Can Be Used with Automatic Mounting
The embossed tape packaging specification of the receptacles permits automatic mounting.
6. Use of Ultra-Fine Teflon Cable
From among the types of suitable cable, O 0.8 mm (single shield) outside diameter ultra-fine Teflon coaxial cable has been made a standard specification in consideration of improving the construction qualities and construction area. An external diameter O1.32 mm (double shield) & O1.13mm (single shield) ultra-fine Teflon coaxial cable specification is also available.
2.5Max
7. Simple Removal of Connectors
The extraction jig permits simple removal of connectors.
8. Mating Checks Are Easy
Subminiature size notwithstanding, the lock sensation permits a check of sure mating.
sApplications
Mobile phones, wireless communications equipment, electronic measuring instruments, GPS, wireless LAN, Bluetooth etc. 2002.3
2.5Max
In comparison with our E.FL Series of SMT coaxial connectors, the receptacles offer a reduction of approximately 18% of the board occupation area resulting in an area of just 7.7 mm2.
U.FL-R-SMT
U.FL-LP-040
3.2Max
1
s Product Specifications
Ratings Nominal characteristic impedance Rated voltage Rated frequency 50o 60 V AC (rms) DC to 6 GHz Operating temperature range Operating humidity -40C to +90C 90% max.
Item
1. Contact resistance 2. Insulation resistance 3. Withstand voltage 4. V.S.W.R.* Dia.0.81Cable Dia.1.13Cable Dia.1.32Cable 5. Female contact holding force 0.15 N min. 6. Repetitive operation Contact resistance
Specification
Center: 20 mo max. Outside: 10 mo max. 500 Mo min. No line or insulation breakdown 1.3 max. 1.35 1.4 1.5 3 to 6 GHz
Conditions
Measured at 10 mA max. Measured at 100 V DC 200 V AC for 1 minute DC to 3 GHz
Measured with a O 0.475 pin gauge 25 mo max. (Center) 15 mo max. (Outside) 30 cycles of insertion and disengagement Frequency of 10 to 100 Hz, single amplitude of 1.5 mm, acceleration of 59 m/s2, for 5 cyles in the direction of each of the 3 axes Acceleration of 735 m/s2, 11 ms duration, sine half-wave waveform, for 6 cycles in the direction of each of the 3 axes Temperature of 40C, humidity of 95%, let stand for 96 hours Temperature: +40C / 5 to 35C / +90C / 5 to 35C Time: 30 min. / Within 5 min. / 30 min. / Within 5 min. Cycles: 5 48 hours continuous exposure to 5% salt water
7. Vibration
No momentary disconnections of 1 s min. No damage, cracks, or parts looseness min. No momentary disconnections of 1 s min. No damage, cracks, or parts looseness No damage, cracks, or parts looseness Insulation resistance 100 Mo min.(High temperature) Insulation resistance 500 Mo min.(Pry) No damage, cracks, or parts looseness Contact resistance 25 mo max. (Center) 15 mo max. (Outside) No excessive corrosion
8. Shock
9. Humidity resistance 9. (Steady state)
10. Temperature cycle 11. Salt spray test
*V.S.W.R. Measurement System The above V.S.W.R. standard values were measured using the measurement system of the diagram below. NOTE 1: Cable type connectors were measured with SMA conversion adapters attached to both ends of the harness product of a suitable 100cm cable. NOTE 2: Board type connectors were mounted to a 50 glass epoxy board and measurements were conducted with SMA conversion adapters attached.
sMaterials
Part Shell Male center contact Female center contact Insulator Plug Receptacle Material Phosphor bronze Brass Phosphor bronze PBT LCP Finish Silver plating Gold plating Gold plating Black Beige Remarks ---------- ---------- ---------- UL94V-0 UL94V-0
2
sPlugs
U.FL-LP-040
Form of Plug After Cable Wiring
U.FL-LP-066 Item HRS No. Part No.
Form of Plug After Cable Wiring
Applicable Cable RF-MF5010 Manufactured by Nissei Electric Co., Ltd. J12B0964 Manufactured by Junkosha Co., Ltd. CO-6F-SB-CX50 Manufactured by Hitachi Cable, Ltd. RF-MF5016 Manufactured by Nissei Electric Co., Ltd. J12B1054 Manufactured by Junkosha Co., Ltd. CL331-0452-5 U.FL-LP-066 A12B0733 Manufactured by Junkosha Co., Ltd. CO-6F-DSB-CX-50 Manufactured by Hitachi Cable, Ltd. 59.1/unit Weight (mg)
Right-angle plug shell (for O 0.81 cable)
CL331-0451-2
U.FL-LP-040
53.7/unit
Right-angle plug shell (for O 1.13 cable) Right-angle plug shell (for O 1.32 cable)
Please order plugs with the cable assembly specifications. sCable Assembly
Dimension of U.FL Series assembly products should be made as indicated below. Single-Ended Cable Assembly Double-Ended Cable Assembly
qOrdering Information
qCable Assembly Overall Length Standard Tolerance
3 4
Overall Length L (mm) 0035U.FL - [] LP - [] - A - (L)
1 1 Series name 2 Assembly type 3 Cable type 4 Overall length (mm) 2
U.FL Blank: Single ended 2: Double ended 04 : For use with O 0.81 cable 5016 : For use with O 1.13 cable 066 : For use with O 1.32 cable Length L is expressed in mm units.
Part No. of Cable Assembly
U.FL-2LP-04-A-(L) U.FL-LP-04-A-(L) U.FL-2LP-5016-A-(L) U.FL-LP-5016-A-(L) U.FL-2LP-066-A-(L) U.FL-LP-066-A-(L)
CL No. 321-1937-2** 321-1998-7** 321-2493-6** 321-2492-3** 321-2170-7** 321-2573-3-
Description Dia. 0.81mm Double Ended Cable Assembly Dia. 0.81mm Single Ended Cable Assembly Dia. 1.13mm Double Ended Cable Assembly Dia. 1.13mm Single Ended Cable Assembly Dia. 1.32mm Double Ended Cable Assembly Dia. 1.32mm Single Ended Cable Assembly
Please contact Hirose Sales Representative about cable length and cable end treatment.
**
3
sReceptacles
NOTE 1: Receptacles of the (01) specification are sold by the pack with 100 pieces per pack. Please order in pack units. NOTE 2: Receptacles of the (10) specification are sold by the reel (which contains 2,500 pieces). Please order in reel units. NOTE 3: Permissible value for mold resin which gets onto the center contact. HRS No. CL331-0471-0-01 CL331-0471-0-10 Part No. U.FL-R-SMT(01) U.FL-R-SMT(10) Sales Quantity Pack sales (100 pieces per pack) Reel sales (2,500 pieces per reel)
(Note 3)
Recommended PCB Footprints
Weight (mg) 15.7/unit
qPackaging Specifications
Embossed Carrier Tape Dimensions
Unreeling direction
Reel Dimensions
4
sConversion Adapter
qSMA Conversion Adapter (Coupling portion: U.FL side jack - SMA side plug)
NOTE: The U.FL side coupling portion has a weaker lock than the regular product and, therefore, cannot be used for purposes other than performance measurements.
HRS No. CL311-0300-2
Product No. HRMP-U.FLJ
qSMA Conversion Adapter (Coupling portion: U.FL side plug - SMA side jack)
NOTE: The U.FL side coupling portion has a weaker lock than the regular product and, therefore, cannot be used for purposes other than performance measurements.
HRS No. CL311-0301-5
Product No. HRMJ-U.FLP
sInspection Receptacle
This receptacle is used for inspecting the continuity, withstand voltage, and other aspects of the harness product.
NOTE: The U.FL side coupling portion does not have a lock and, therefore, cannot be used for purposes other than continuity and withstand voltage inspections.
HRS No. CL331-0466-0
Product No. U.FL-R-1
sExtraction Jig
This jig is used for extraction from a coupled condition.
90 50
U.FL
O15
5 2.1
HRS No. CL331-0494-5 CL331-0441-9
Product No. U.FL-LP-N-2 E.FL-LP-N-2
5
sUsage Precautions
1. Plugs
1) To disconnect connectors, hook the end portion of E.FL-LP-N and U.FL-LP-N-2 onto the connector cover and pull off vertically in the direction of the connector coupling axis. 1) To remove the connector directly, hold the connector cover and pull off U.FL-LP-N-2 vertically in the direction of the connector coupling axis. (Please exercise E.FL-LP-N caution so as not to injure fingertips or nails.) U.FL-LP-040 U.FL-LP-066 2) To couple the connectors, the coupling axes of both connectors are aligned and the connectors are inserted as perpendicularly as possible. Do not attempt to insert on an extreme angle.
U.FL-R-SMT
(1) Connection/ disconnection of connectors
After the connectors are coupled, do not apply a load to the cable in excess of the values indicated in the diagram below.
U.FL-LP-040
2N or less
(2) Permissible load on the cable after connector coupling.
U.FL-R-SMT 4N or less
2N or less
(3) Precautions
Please note that excessive twisting in the action of insertion or removal will cause damage.
2. Receptacles
Recommended Temperature Profile (Reference)
(1) Recommended temperature profile (Reference)
1) The temperature indicates the printed circuit board surface temperature of the connector lead portion. 2) The reflow soldering method should be performed at a peak temperature of 240C or less at the surface of the printed circuit board. 3) The temperature profile will change depending on conditions which include such factors as the size of the board, the solder used, and the solder thickness. (2) Recommended hand soldering conditions (Reference) Soldering iron temperature: 350C Soldering time: Within 5 seconds
(3) Recommended screen 0.15 mm thickness
6

▲Up To Search▲

Price & Availability of UFL-LP-040

	To Download UFL-LP-040 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .